Open Car Windshield Parts

|
Show 9 Of 12
Showing 9 Of 12 results
Part # A-37118 | Model Year 28-36
Mount on the lower horizonal part of the windshield frame for pulling it shut. On all open cars.
DISCONTINUED
Temporarily
OUT OF STOCK
$15.50 PR
Part # A-37154-RC Model Year 30-31
Part # A-37154-RP Model Year 28-31
Part # WEB-KIT-1048 | Model Year 28-31
Installs between windshield frame and windshield stanchions at the pivot point. Open cars only. These are a quality American made cone with the proper taper. U.S.A.
DISCONTINUED
Temporarily
OUT OF STOCK
Part # A-37130-ST | Model Year 30-31

Lower windshield stanchions for the windshield in plain steel.  Used on all 1930-31 Roadsters, Roadster Pickup, and Phaeton. They include the fine threaded stud that secures the upper stanchion to it. Sold in pairs only.  U.S.A.

DISCONTINUED
Temporarily
OUT OF STOCK
$149.95 PR
Part # A-1013-B | Model Year 30-31
These bronze castings are used on all Roadsters, Roadster Pickups, and Phaetons. They go at the top of the cowl. These are what the stanchion screws that hold the lower stanchions screw into. U.S.A.
DISCONTINUED
Temporarily
OUT OF STOCK
$275.00 PR
Part # #16-A Model Year 28-31
Part # #16-B Model Year 31-31
Part # #16-C Model Year 28-29
Part # WEB-KIT-1045 | Model Year 28-31
A set of 4 screws that hold the windshield stanchions to top of the cowl post on 1928-31 Roadster, Roadster Pickup, and Phaetons.  USA
DISCONTINUED
Temporarily
OUT OF STOCK
Part # A-37130-1 | Model Year 30-31
Lead spacer used between the dash rail and the lower stanchion. Come molded in a pair, so you will have to break them apart at the seam. U.S.A.
DISCONTINUED
Temporarily
OUT OF STOCK
$7.95 PR
Part # A-37158 | Model Year 21-31
Open cars used these studs where the windshield pivoted. Special thin cone shaped nut for holding the frame cones are included. Set consists of 2 studs and 2 nuts. U.S.A.
DISCONTINUED
Temporarily
OUT OF STOCK
$13.95 SET
Part # A-37199-A Model Year 28-29
Part # A-37199-B Model Year 30-31
Part # WEB-KIT-1049 | Model Year 28-31

The rubber gaskets needed for the windshield of the open cars.

1928-29 has a strip that inserts into the bottom of the windshield frame and a different profile that installs in the windshield stanchion to seal the side.

1930-31 uses a 1" x 46" long "T" shaped piece in the bottom of the windshield frame and a 1/2" x 32" "T" shaped piece that inserts in the vertical sides of the frame to seal the sides.  USA

DISCONTINUED
Temporarily
OUT OF STOCK
Part # A-37137-L Model Year 26-31
Part # A-37137-S Model Year 26-31
Part # WEB-KIT-1046 | Model Year 26-31

The steel cup-like sockets mounted in the stanchions. If you are ordering new stanchions, these will already be installed in them.

The small one is used where the windshield pivots at the top of the stanchion. 

The large is used on the bottom of the 30-1 windshield stanchion where it pivoted on the lower stanchion.  U.S.A.

DISCONTINUED
Temporarily
OUT OF STOCK