Floorboard Screws Set of black oxide screws and
special washers for mounting
the floorboards in the car. U.S.A.
Floorboard Washers The special countersunk
washer used in mounting the
floorboards. Also used for mounting some of the door hinges. USA
Floorboard Screws Set of black oxide screws and
special washers for mounting the
center and rear floorboards in the
Tudor Sedan.
Pedal Seal Early 28's with the multiple disc
clutch used this rubber pad
around the pedals and steering
column. USA
Pedal Plates (Drop) These special plates are only
used on the A-400, Vicky,
Deluxe Phaeton, or any other
model A with the dropped
steering column.
RHD Pedal Seal Rubber pad used to seal
around the pedals and the
steering column on right hand
drive model A's.
Felt Pad A heavy felt pad fitting tight around
steering column and pedals. Use
with metal plates above. U.S.A.
Plate Mounting Screws Contains 3 trim washers, 1
wood screw, and 2 machine
screws for mounting the A-35123-SP plates to the floor. U.S.A.
Pedal Plates A two piece steel plate for
holding the felt around the
steering column and the
pedals. Keeps engine fumes
from entering the car. Keeps cold out. U.S.A.
Storage Box There is never enough room when touring. This handy unit mounts under the rear floorboard of Tudor sedans and gives you two compartments that are 9" wide, 14" long, 10" deep. Unit is held in place by the...
No Image Available
Tudor Sedan Rear Floorboards The Tudor Sedans used a wood floor board instead of a metal floor pan. There was one under the drivers seat and one in the back seat area. USA
Street Rod Floorboard Kit This steel floorboard
kit is made to replace
the original wooden
floorboards in the
front of your A. This kit can only be used with the ?BITCHIN? brand recessed firewalls. U.S.A.
Street Rod Floor Kit This kit is
made to work
with the Bitchin
brand recessed firewalls. Runs the full length of the floor. USA
A-35130-HRC 1928-31
Fits:1928-31 Tudor, Roadster, Phaeton, and 1928-29...
Floorboard Seal Black cotton webbing
with tacks that gets put
around the edge of the floorboards to seal them up. Nails to outside edge, then folds under the board and gets nailed to bottom as
well. USA
A-35130-S 1928-31...
Floorboards A 2 piece set for the front
of your model A. All holes
are drilled for mounting. The finest you can buy! Made from 7-ply birch hardwood veneer. USA
Emergency handle to front of gear shift:
A-35130/31-A 1928-29...
Floorboard Irons These metal straps were
riveted to the bottom side
of the floorboard to support the middle of the front angled floorboard. Comes with mounting rivets as original. U.S.A.
Early Floorboard Irons Used from the beginning of
production until around
March of 1928. These
attached to the under-
side of the floorboards for reinforcement. Held
on with flat headed wood screws which are
included....
Battery Cover Plate The cover that snaps into the
opening over the battery in
the floorboards. Made of heavy gauge steel with spring steel retaining clips riveted in place. Plates are powder coated black and even have...
Clutch Plate Early 28's with the emer-
gency brake to the left had
this plate installed in the floorboards
to allow access to grease the clutch release
bearing. USA
Accelerator Rod Grommet Round rubber pad and mounting
tacks to seal out the dust in the
summer, and the cold air in the winter. Just like the original. U.S.A.
